Curtiss P-40D/E Kittyhawk Mk I/IA

The new fighter became an instant hit with the British, who ordered the new design right off the drawing board in May 1940. In British service the fighter would receive Kittyhawk Mk I designation (factory designation H-87A-21). Altogether 560 aircraft were built for the RAF (serial numbers AK571 to AK999 and AL100 to AL230) and delivered between August and December 1941. Only the first twenty examples (AK571 to AK590) carried four wing-mounted weapons – the remaining aircraft were armed with six machine guns. The first Kittyhawk Mk I (AK 571) was flight tested on May 22, 1941. The RAF handed over 72 Kittyhawk Mk Is to the Canadians, one ended up in Australia as a training airframe and 24 examples were delivered to Turkey.

PS05 zdj3

USAAC did not order the new fighter until September 13, 1940. The aircraft received P-40D service designation (factory designation Model 87A). Initially 323 aircraft were ordered (plus one slightly modified Model 87B example), but eventually USAAF2 took delivery of only 22 machines in July 1941 (s/n 40-359 and 40-361 to 40-3813) in favor of the P-40E version. The P-40D model had a very short career in USAAF service: in October 1942 all remaining examples were withdrawn from line units and sent to training squadrons with a new RP-40D designation (the letter R stood for “restricted from combat use”).
Simultaneously with the development of Model 87A Curtiss engineers were working on its sister design, Model 87B. The principal difference between the two was the weapons fit: Model 87B features six wing-mounted .50 cal (12.7 mm) machine guns, which was to most of the RAF Kittyhawk Mk I configuration. The ammunition supply was 240 rounds for each inside gun, 291 rounds for each middle gun and 312 rounds for each outside weapon4. The installation of additional weapons meant that gun bay access panels under the wings had to be enlarged. By the same token the option for internal 20 mm cannon was no longer available. The aircraft was factory configured to accept underwing Q-2 bomb racks, each capable of carrying three light fragmentation bombs – 20 lb (9 kg) M42, or 30 lb (13.6 kg) M5. The area just behind pilot’s headrest received additional armor protection. All those modifications further inflated the aircraft’s weight (loaded weight went up to 8,280 lb [3,756 kg]) and degraded its performance in terms of service ceiling, range and rate of climb. However, production machines had slightly higher top speed performance due in part to new “fishtail” exhaust stack design.

PS05 zdj4

The first example of the new version, USAAC designation P-40E (s/n 40-358), was ordered at the same time as the production P-40D aircraft. On February 18, 1941 a decision was made to deliver the remaining 300 machines from the original P-40D order upgraded to the P-40E standard (s/n 40-382 to 40-681). At the same time the USAAC ordered additional 519 P-40E models (s/n 41-5305 to 41-5744 and 41-13521 to 41-13599). Several further modifications were introduced during the production run. Beginning with s/n 40-480 a new, twin-layer windshield was installed with hot air circulation between the layers. The true self-sealing tanks (similar to the ones in the P-40C model) were installed beginning with s/n 40-584. Finally, beginning with s/n 41-5521, the original SCR-283 VHF radio was replaced with an SCR-274 or an SCR-522A unit.
Eventually 820 P-40Es (Model 87B-2) were delivered to the U.S. units. The P-40E became the first P-40 variant to be mass-produced for the USAAF. The deliveries began in August 1941 and were completed by May 1942. Only four Pursuit Squadrons received the new fighters before the U.S. entered the war: two from the Philippines-based 24th Pursuit Group (3rd PS at Iba and 17th PS at Nichols Field), 21st PS from 35th PG (also deployed to the Philippines) and 79th PS from 20th PG based at Hamilton Field, California. Two P-40E examples were later converted into trainers by adding a second cockpit with an independent sliding canopy in place of the fuselage fuel tank. The aircraft (one of them was s/n 40-582) were redesignated TP-40E5.


PS05 zdj5

Once again, the British were very much interested in the acquisition of the new P-40 model and the RAF promptly placed an order for 1,500 fighters (RAF serials ET100 to ET999 and EV100 to EV699). Since the aircraft were ordered and paid for by the U.S. Government and delivered to Great Britain under the provisions of the Lend-Lease Act, they were also given USAAF serial numbers: 41-24776 to 41-25195 and 41-35874 to 41-36953. In RAF service they were known as Kittyhawk Mk IA (to distinguish them from almost identical Mk I fighters), while USAAF machines received the P-40E-16 designation (factory designation H-87A-47). The deliveries took place between December 1941 and June 1942.
Kittyhawk Mk IAs differed from American P-40Es in some configuration details: they featured a rear view mirror mounted externally on the windshield frame (left of the centerline), a provision for a traditional ring-and-bead gun sight in front of the windshield and the lack of bleed air heating installation of the carburetor air scoop assembly. U.S. Q-2 bomb racks were replaced with two British units, each capable of carrying five 25 lb (11.3 kg) fragmentation bombs. Most of the fighters delivered to Great Britain had factory-installed centerline pylon. Majority of the aircraft from the first delivery batch (s/n 41-24776 to 41-25195 and 41-35874 to 41-36353, RAF serials ET100 to ET999) retained their blue formation lights on the fuselage. Furthermore, the first 400 or so machines delivered to the RAF featured a British style pitot tube and the gun camera housed in a pod under the starboard wing (similar to the P-40D and Kittyhawk Mk I), while the remaining machines had a straight, U.S. style pitot tube and the gun camera located in the forward part of the starboard landing gear fairing (as in the P-40E). The last 200 examples of P-40E-1 (s/n 41-36754 to 41-36953, RAF serial EV500 to EV699) featured manual gun charging and a provision for an antenna mast installation. Late production P-40E-1s were additionally equipped with a slightly enlarged vertical stabilizer with a small dorsal fin at its root, a design feature common to the P-40K-1 and K-5 versions. That particular vertical stabilizer design feature was to improve lateral stability that was somewhat worse than in the P-40 and P-40B/C models.

PS05 zdj6


RAF Kittyhawks saw service mainly in the MTO8, i.e. North Africa, Middle East and, later, in Italy and in the Balkans. Several Commonwealth units in the MTO also operated the type, e.g. No. 3 and 450 Sqn RAAF, or No. 2, 4, 5 and 11 Sqn SAAF. The aircraft may have been inferior to the modern fighter types flown by the Axis pilots, but they fared well in the fighter-attack role due to their sturdy design, respectable range and good armament fit. Over 1,000 P-40E/E-1 aircraft were delivered to other allied nations, both directly from the USA or through RAF: 163 examples were delivered to Australia, 62 to New Zealand, 57 to China (in fact the aircraft went to American Volunteer Group, which became 23rd Fighter Group, USAAF in July 1942), 12 to Canada, 6 to Brazil, 22 to South Africa and 691 to the Soviet Union. As an interesting side note, a dozen or so captured P-40Es were flown by the Imperial Japanese Army Air Force. After the U.S. entered the war some of the P-40E-1s earmarked for Great Britain were pressed into USAAF service.

PS05 zdj7

Between 1941 and 1942 a high altitude P-40J version was briefly contemplated. The aircraft was to be a modification of a basic P-40E with a turbosupercharged engine. The idea was discarded in May 1942.

Technical description
P-40D/E was a cantilevered, low wing, all metal semi-monocoque design with fabric covered control surfaces. It featured a three-spar tapered wing with rounded wingtips. The wing was equipped with conventional ailerons and split flaps. Port and starboard wing sections were mated prior to fitting to the fuselage structure. The wing featured a +6° dihedral along the span, the leading edge was swept back at 1°18’, wing incidence angle was +1°. The NACA 2215 airfoil was used at the wing root, changing to NACA 2209 at the wing tips. The maximum flap extension was 45°; the ailerons moved 18°45’ upwards and 10°30’ downwards. The trailing edge flaps had a span of 10 ft 2 in (3.1 m) and the ailerons spanned 6 ft 11 in (2.12 m). The cantilevered taiplane was of a conventional design. Vertical stabilizer was offset to the left at 1°30’ in relation to the fuselage centerline. The rudder movement was 30° each way. The rudder height was 6 ft 3 in (1.89 m). Horizontal stabilizers had an angle of incidence of +2° and spanned 12 ft 10 in (3.90 m). Elevators moved 30° up and 20° down. Rudder and elevators were equipped with trim tabs. Rudder trim tab moved 15° each way, while elevator tabs moved 30° up and 26° down.

Read more…

PS05 okl

  • Recommended - Armour

History of the 40/43M Zrínyi Assault Howitzer
History of the 40/43M Zrínyi Assault Howitzer The lessons learned from the ongoing war already proved the combat...
History of the  Turán Medium and Heavy Tanks  in World War II
History of the Turán Medium and Heavy Tanks in World War II The Hungarian Army made serious efforts to build up an independent,...
German Medium Tank  Panzerkampfwagen III  from Ausf. H to Ausf. N
German Medium Tank Panzerkampfwagen III from Ausf. H to Ausf. N In the mid-1930s German authorities intensified their efforts...
Renault FT & M1917 Light Tanks
Renault FT & M1917 Light Tanks During its 25-year service, the Renault FT tank was used in many...
Operational History of the Hungarian Armoured Troops in World War II
Operational History of the Hungarian Armoured Troops in World War II In 1938, concurrently with German territorial demands, Hungary...